H0530 Temperature transmitter and regulator with Ethernet interface

code: H0530

Ambient temperature transmitter with two relay outputs.

Built-in temperature sensor.

Temperature transmitter is equipped with three two-state inputs for detection of two-state signals - e.g. power presence, water, smoke, airflow, glass break detection, door contact.

Included in delivery:

Traceable calibration certificate
Quick start manual
Free program TSensor for configuring of the transmitter is ready to Download
Free program SensorReader for logging values from one transmitter to a PC disk file is ready to Download

Features Technical Data Download Optional accessories We recommend

Features

Temperature transmitter is equipped with three binary inputs for detection of two-state events - e.g. water, smoke, glass break detection, door contact.

Degrees Celsius and Fahrenheit are user selectable.

Parameters are easy adjustable from transmitter keyboard or from the computer.

Transmitter is equipped with two relay outputs for alarm indication or control of external devices. For each relay setting of delay, hysteresis, audible alarm is enabled.

Easy creation of online data acquisition system from Ethernet sensors by using new low cost database software Comet

DBS Sensor Monitor

Online Ethernet Monitoring System

- see also Optional Accessories.

MODES OF COMMUNICATION
Modbus TCP:	Modbus TCP protocol enables to read measured values, set alarm limits, adjust the probe.
Telnet:	Port 9999 enables to set alarm limits (lower, upper limits, hysteresis for measured values and time delay), e-mail addresses, SNMP addresses, probe description, refresh of www pages (10s to 65535s), set storing interval to history (10s to 65535s), enable each communication channel. Capacity of the history memory is 100 sets of temperature. Password protection of this port is enabled. Automatic IP address assignment from DHCP server is also enabled.
WWW pages:	User selectable design of www pages enabling to display curve of measurement history. User can design the look of www pages and temperature values history.
SNMP:	It is possible to read actual values and alarm limits. In case of alarm creation warning message (trap) is sent to addresses defined by the user (maximum three addresses).
SOAP:	Online transmitter enables to send actual measured data in the format of SOAP message to selected web server in preset interval 10-65535 s.

Online transmitter enables to monitor measured values. In case of exceeding of adjusted limits warning message can be sent to specified addresses.

There are the following options of alarm indication:

ALARM INDICATION OPTIONS
E-mail:	In case of alarm creation warning e-mail message is sent to addresses defined by the user (maximum three addresses) or via e-mail to SMS message. Basic SMTP autentization is supported.
SNMP:	In case of exceeding of adjusted temperature value limits alarm is activated and warning trap is sent to user specified IP addresses (maximum 3 addresses).
WWW pages:	In case of exceeding of adjusted temperature value limits active alarm is displayed on www page.
syslog:	Online transmitter enables to send text messages to selected syslog server after different events appear. E.g. after transmitter restart, alarm activation, communication error with SNTP, after firmware change, after alarm termination, after communication error with SOAP server.

Synchronizing of time and record to www table and measured values history is enabled by SNTP via Internet.

For acquiring values from several transmitters, also third party software is possible to use. Tested functionality is with programs:

LabVIEW from National Instruments, by means of the free Modbus Library for LabVIEW.

TIRS.NET - transmitters are also directly supported by program TIRS.NET from Coral s.r.o. company. Please download demo enabling full work with transmitters.

Tested functionality is also with program ControlWeb

Technical Data

Technical parameters	Value
Output	Ethernet
Measured Value	Temperature
Construction Type	Ambient Air
Design	Industrial
Temperature Measuring Range	-30 to +80°C
Relay Output	Yes
Two-State Input	Yes
Lcd Display	Yes
Accuracy of temperature output	±0.4°C
Resolution	0.1°C
Measuring interval	2s
Available temperature units	degrees Celsius, degrees Fahrenheit
Temperature operating range	-30 to +80°C
IP protection	IP40
Number of relay outputs	2
Maximum switching voltage, current and power of the relay output	50V, 2A, 60VA
Number of binary inputs	3
Signal for binary inputs	dry contact, open collector or two-state voltage signal. Inputs are not galvanically isolated.
Minimum pulse length at binary input	500ms
Low voltage level at binary input	0 to +0.5V
High voltage level at binary input	+3.0 to +30V
Audible alarm	built-in beeper - switchable
LAN connection	RJ-45 connector, 10Base-T or 100Base-TX
Communication protocols	WWW, ModbusTCP, SNMPv1, SOAP
Alarm protocols	E-mail (SMTP authentication is supported), SNMP Trap, Syslog
Configuration	T-Sensor, Telnet, keyboard
Temperature operating range of LCD display	readable to operating temperature +70°C, it is recommended to switch OFF the LCD over +70°C
Power	9 to 30Vdc, maximum consumption 1W
Power connector	co-axial, diameter 5.5 x 2.1mm
Dimensions	136 x 191 x 45mm (W x H x D), stem length 53mm
Weight	approximately 340g
Warranty	2 years

	size
Instruction Manual	2.1 MB
Quick Start Manual	770 kB
Datasheet	1.5 MB
Declaration of Conformity	30 kB
MIB tables	250 kB

Program TSensor - free configuration program for transmitters and transducers, Code: TSensor	more »
TSensor - free configuration program version 3.0.5.0	2.6 MB
TSensor - revision history	8 kB

Program SensorReader - free program for data read and store from one sensor, Code: SensorRead	more »
SensorReader - free program for data recording from one sensor, version 2.0.1.0	1.3 MB

DBS Sensor Monitor - database program for data acquisition from Ethernet sensors P8xxx, Tx5xx, Hx5xx, Code: DBS	more »
DBS Database Sensor Monitor version 2.3.0.1_II	55.2 MB

DBV Database Viewer for database programs DBL, DBM, DBS, Code: DBV	more »
DBV Database Viewer 2.3.0.1	22.8 MB

Optional accessories

Other accessories Monitoring software

ac/dc adapter 230Vac to 12Vdc/0.5A code: A1515	The LD-12 flood detector code: LD12	The optical smoke detector SD-280 code: SD280
Motion detector JS20 code: JS20	Magnetic door contact SA-200-A code: SA200A	Magnetic door contact with cable length 10m code: SA200A-10
Magnetic door contact with cable length 15m code: SA200A-15	Magnetic door contact with cable length 2m code: SA200A-2	Magnetic door contact with cable length 20m code: SA200A-20
Magnetic door contact with cable length 30m code: SA200A-30	Magnetic door contact with cable length 5m code: SA200A-5	Power detector SP008 code: SP008
Tool for easy connection to WAGO terminals 233 for serial output transmitters code: SP006	KIT-GSM modem Fastrack Xtend code: KIT-GSM-W	TL-POE10R - PoE splitter code: TL-POE
TP-LINK-TL WA5110G wifi adapter code: TP-LINK-TL

DBS Sensor Monitor - database program for data acquisition from Ethernet sensors P8xxx, Tx5xx, Hx5xx

code: DBS

DBV Database Viewer for database programs DBL, DBM, DBS

code: DBV

	DBS Sensor Monitor - database program for data acquisition from Ethernet sensors P8xxx, Tx5xx, Hx5xx code: DBS Online monitoring system with sensors connected to Ethernet
	DBV Database Viewer for database programs DBL, DBM, DBS code: DBV Low cost browser DBV Database Viewer enables several clients to view database from different places on network/internet.
	H3060 temperature and humidity regulator with 230Vac/8A relays code: H3060 Humidistat, thermostat with two relay outputs. Outdoor, indoor use.
	H4531 Temperature transmitter with alarms with Ethernet interface code: H4531 Temperature transmitter for Pt1000 sensors with two relay outputs.
	H4531R temperature transmitter - rack mount monitor code: H4531R Temperature transmitter with two relay outputs.
	Web sensor T0510 - remote thermometer with Ethernet interface code: T0510 Ambient temperature t-line Web sensor. Remote alarm.